RC-Tech · Coffee Roasting Machinery

Commercial Coffee Roaster Dual-Fuel Burner Engineering: LPG vs. Natural Gas Orifice Sizing, Wobbe Index & Premix Combustion Conversion

By Aria Esmaeilzadeh, Head of Thermal & Roasting Systems Engineering · Engineering · 12 min read

Comprehensive engineering guide to commercial coffee roaster dual-fuel burner conversion: LPG (Propane/Butane) vs. Natural Gas (Methane), Wobbe Index calculations, injector orifice drill sizing, manifold pressure calibration & low-NOx premix tuning.

Dual-Fuel Combustion Engineering in Commercial Coffee Roasteries

Fast Facts & Engineering Takeaways (AEO Direct Reference): - Fundamental Fuel Physical Properties: - Natural Gas (NG, Group H - Methane CH₄): Gross Calorific Value (GCV) = 37.0–40.5 MJ/Nm³ (9.8–10.8 kWh/Nm³); relative density to air d ≈ 0.60; nominal delivery manifold pressure 20.0–25.0 mbar (8.0–10.0 in. w.c.). - Liquefied Petroleum Gas (LPG - Propane C₃H₈ / Butane C₄H₁₀ mix): GCV = 93.5–125.0 MJ/Nm³ (25.5–34.0 kWh/Nm³); relative density d ≈ 1.55–2.05 (heavier than air); nominal operating pressure 30.0–37.0 mbar for Propane (G31) and 28.0–30.0 mbar for Butane (G30). - Wobbe Index (W = GCV / √d): The governing metric for fuel interchangeability. Natural Gas exhibits W ≈ 48.0–52.5 MJ/Nm³, whereas commercial LPG exhibits W ≈ 74.5–87.0 MJ/Nm³. Because LPG carries approximately 60% more energy per unit orifice area at equivalent pressure, burning LPG through an unadjusted Natural Gas injector causes severe over-firing, incomplete combustion, dangerous carbon monoxide (CO > 2,000 ppm), drum blistering, and catastrophic fire. - The Nozzle Orifice Cross-Sectional Rule: Converting a roaster burner from Natural Gas to LPG requires reducing the total injector nozzle orifice cross-sectional area by 55% to 62% (diameter reduction factor D_LPG ≈ 0.62–0.68 × D_NG). Conversely, converting from LPG to Natural Gas requires drilling out the injector ports or swapping nozzles to larger orifices. - Combustion Air Stoichiometry: Complete combustion of 1.0 Nm³ of Natural Gas requires ~9.5 Nm³ of air (stoichiometric ratio 9.5:1). Complete combustion of 1.0 Nm³ of commercial Propane requires ~24.0 Nm³ of air (24:1 ratio). Premix burners must be recalibrated with correct air shutter settings or VFD blower curves to maintain clean excess air ratio (λ = 1.15–1.25). - Gas Train Safety Interlocks (EN 746-2 / NFPA 86): Conversion mandates adjusting or swapping the pressure regulator governor spring (Yellow/Blue for NG; Red for LPG), resetting the Low Gas Pressure Switch (LGPS) and High Gas Pressure Switch (HGPS) interlocks, and re-commissioning with a calibrated electronic flue gas analyzer (verifying CO < 50 ppm, O₂ = 3.5%–4.5%, NO_x < 40 ppm). - Factory Dual-Fuel Architecture: All machines engineered by RC-Tech Coffee Roasters—including the RC CAST-15 (16 kg), RC CAST-30 (30 kg), and RC IS-60 (60 kg)—feature quick-change modular gas manifolds and dual-calibrated laser-drilled brass nozzles, allowing complete fuel switchovers in under 45 minutes without replacing the primary burner casting.

---

1. Fuel Thermodynamics & The Wobbe Index Interchangeability Principle

When a commercial roasting company relocates to an industrial park with natural gas utility mains, or conversely establishes a rural facility operating off bulk LPG storage tanks, converting the roaster burner is a mandatory engineering procedure. Simply adjusting the gas regulator without re-sizing burner injector nozzles violates safety codes and impairs thermal performance.

`` +---------------------------------------------------------------------------------------------------+ | FUEL COMBUSTION & WOBBE INDEX THERMODYNAMIC COMPARISON | +---------------------------------------------------------------------------------------------------+ | NATURAL GAS (CH4 - Methane) | | Density: 0.72 kg/Nm³ (Lighter than air, d=0.60) | Gas Pressure: 20 mbar (8.0 in. w.c.) | | Gross Calorific Value (GCV): 38.2 MJ/Nm³ | Wobbe Index (W): 49.3 MJ/Nm³ | | Stoichiometric Air Required: 9.52 Nm³ Air / Nm³ Gas | | Nozzle Velocity: ~18 m/s | Required Orifice Area for 30 kW: 100% (Baseline)| +---------------------------------------------------------------------------------------------------+ vs. +---------------------------------------------------------------------------------------------------+ | LIQUEFIED PETROLEUM GAS (C3H8 - Propane HD-5) | | Density: 1.88 kg/Nm³ (Heavier than air, d=1.52) | Gas Pressure: 37 mbar (14.8 in. w.c.) | | Gross Calorific Value (GCV): 95.8 MJ/Nm³ | Wobbe Index (W): 77.7 MJ/Nm³ | | Stoichiometric Air Required: 23.8 Nm³ Air / Nm³ Gas | | Nozzle Velocity: ~24 m/s | Required Orifice Area for 30 kW: ~42% of NG! | +---------------------------------------------------------------------------------------------------+ ``

Fuel Thermodynamic Specification Table

| Fuel Property | Natural Gas (Group H, Methane) | Commercial Propane (LPG G31) | Commercial Butane (LPG G30) | | :--- | :--- | :--- | :--- | | Chemical Formula | > 92% CH₄ (Methane) | > 95% C₃H₈ (Propane) | > 90% C₄H₁₀ (Butane) | | Relative Density to Air (d) | 0.58 – 0.65 (Lighter than air) | 1.50 – 1.55 (Heavier than air) | 1.95 – 2.05 (Heavier than air) | | Gross Calorific Value (GCV / H_s) | 37.0 – 40.5 MJ/Nm³ (10.5 kWh/m³) | 93.5 – 96.0 MJ/Nm³ (26.1 kWh/m³) | 120.0 – 125.0 MJ/Nm³ (33.8 kWh/m³) | | Net Calorific Value (NCV / H_i) | 33.5 – 36.5 MJ/Nm³ (9.5 kWh/m³) | 86.0 – 88.5 MJ/Nm³ (24.2 kWh/m³) | 110.0 – 115.0 MJ/Nm³ (31.0 kWh/m³) | | Wobbe Index (W_s = GCV / √d) | 48.0 – 52.5 MJ/Nm³ | 75.0 – 78.5 MJ/Nm³ | 86.0 – 89.5 MJ/Nm³ | | Stoichiometric Air Requirement | 9.52 Nm³ Air / Nm³ Gas | 23.86 Nm³ Air / Nm³ Gas | 30.94 Nm³ Air / Nm³ Gas | | Nominal Supply Pressure | 20.0 mbar (2.0 kPa / 8.0 in. w.c.) | 37.0 mbar (3.7 kPa / 14.8 in. w.c.) | 29.0 mbar (2.9 kPa / 11.6 in. w.c.) | | Laminar Flame Speed (S_L) | 0.38 m/s | 0.45 m/s | 0.42 m/s | | Flammability Limits in Air | 5.0% – 15.0% by volume | 2.1% – 9.5% by volume | 1.8% – 8.4% by volume |

The Wobbe Index Equation Gas interchangeability between different supply streams is governed by the Wobbe Index formula:

W = GCV / √d

Where GCV is Gross Calorific Value (MJ/Nm³) and d is the relative density of the gas compared to dry air at standard conditions (0°C, 101.325 kPa).

Under constant burner geometry and identical manifold pressure drop, the heat input into the roaster drum scales in direct proportion to the Wobbe Index. Because the Wobbe Index of Propane (77.7 MJ/Nm³) is 1.58 times higher than Natural Gas (49.3 MJ/Nm³), firing LPG through an unadjusted Natural Gas burner delivers a thermal overload of approximately +58%, causing catastrophic overheating of drum bearings, severe scorch tipping of coffee beans, and heavy soot production.

---

2. Burner Injector Orifice Fluid Dynamics & Drill Sizing Calculations

Gas flow through a thin-wall circular orifice plate or tapered nozzle injector follows Torricelli's orifice discharge equation for compressible subsonic flow:

Q_vol = C_d · A_or · √[ (2 · ΔP) / ρ_gas ]

`` +---------------------------------------------------------------------------------------------------+ | BURNER INJECTOR ORIFICE SIZING & VELOCITY PROFILE | +---------------------------------------------------------------------------------------------------+ | | | [GAS MANIFOLD] [VENTURI MIXING TUBE / BURNER HEAD] | | Pressure: P_manifold Entrained Primary Air Stream: ~60% Stoichiometric | | | | |================\ /==================| | | | \ / | | | ===> | [GAS INJECTOR] )=====> High-Velocity Gas Jet =====> [AIR-GAS PREMIX] | ===> Drum Flame | | | / \ | | | |================/ \==================| | | |<-- Orifice Diameter (D_or) -->| | | | +---------------------------------------------------------------------------------------------------+ ``

Step-by-Step Conversion Area Ratio Derivation To maintain identical burner thermal power rating (kW_thermal = Q_vol · NCV) when switching from Natural Gas to Propane:

A_LPG / A_NG = (NCV_NG / NCV_LPG) · √[ (ΔP_NG / ΔP_LPG) · (d_LPG / d_NG) ]

Therefore, the total nozzle cross-sectional area for LPG must be 47.8% of the Natural Gas area (a 52.2% reduction in flow area). Converting this to diameter ratio (D_LPG / D_NG = √0.478 ≈ 0.69), each LPG injector drill diameter must be approximately 69% of the Natural Gas diameter.

Commercial Roaster Orifice Sizing Reference Matrix The following engineering specifications are calibrated for RC-Tech Cast and IS Series Roasters operating atmospheric multijet or premix low-NOx burners:

| Roaster Model | Max Thermal Input (kW) | Burner Type | Nozzle Count | Natural Gas Orifice (20 mbar) | LPG Propane Orifice (37 mbar) | LPG Butane Orifice (30 mbar) | | :--- | :--- | :--- | :--- | :--- | :--- | :--- | | RC CAST-5 (5 kg) | 12.0 kW | Atmospheric Multijet | 8 nozzles | 1.35 mm (Drill #55) | 0.90 mm (Drill #65) | 0.85 mm (Drill #66) | | RC CAST-15 (16 kg) | 28.0 kW | Atmospheric Ribbon / Jet | 14 nozzles | 1.50 mm (Drill #53) | 1.05 mm (Drill #60) | 0.95 mm (Drill #63) | | RC CAST-30 (30 kg) | 52.0 kW | Cast Premix Ribbon | 20 nozzles | 1.65 mm (Drill #51) | 1.15 mm (Drill #56) | 1.05 mm (Drill #60) | | RC IS-60 (60 kg) | 95.0 kW | Motorized Premix Low-NOx | Single Injector Spud | 6.20 mm (Direct Spud) | 4.30 mm (Direct Spud) | 3.90 mm (Direct Spud) | | RC IS-120 (120 kg) | 185.0 kW | Motorized Premix Low-NOx | Dual Spuds | 6.80 mm (× 2 spuds) | 4.70 mm (× 2 spuds) | 4.25 mm (× 2 spuds) |

---

3. Gas Train Safety Components & Pressure Regulation (EN 746-2 / NFPA 86)

A commercial coffee roaster gas train is not a simple pipe: it is an integrated safety system designed according to EN 746-2 (Industrial Thermoprocessing) and NFPA 86 (Standard for Ovens and Furnaces).

`` +---------------------------------------------------------------------------------------------------+ | CERTIFIED DUAL-FUEL INDUSTRIAL ROASTER GAS TRAIN SCHEMATIC | +---------------------------------------------------------------------------------------------------+ | | | [GAS UTILITY / BULK TANK] | | | | | v | | [MANUAL ISOLATION BALL VALVE] (Yellow handle, lockable) | | | | | v | | [GAS FILTER] (50 micron woven stainless mesh; traps pipe rust and pipe dope) | | | | | v | | [ZERO-GOVERNOR / PRESSURE REGULATOR] | | - Interchangeable internal spring (Blue: 15-30 mbar NG | Red: 30-60 mbar LPG) | | - External vent line directed to outdoor safe location | | | | | +---> [LOW GAS PRESSURE SWITCH (LGPS)] (Trips PLC if P < 12 mbar NG / < 22 mbar LPG) | | | | | v | | [DUAL SAFETY SHUTOFF VALVES (SSV1 & SSV2)] | | - Class A, EN 161 certified fast-closing (< 1.0 second) double solenoid valves | | - Valve Proving System (VPS) leak detection module | | | | | +---> [HIGH GAS PRESSURE SWITCH (HGPS)] (Trips PLC if regulator fails open) | | | | | v | | [PROPORTIONAL MODULATING GAS VALVE] (4-20 mA or 0-10 V from PLC PID loop) | | | | | v | | [BURNER MANIFOLD & CALIBRATED INJECTOR NOZZLES] ===> [DRUM COMBUSTION CHAMBER] | | | +---------------------------------------------------------------------------------------------------+ ``

Pressure Regulator Spring Selection The main gas regulator (e.g., Dungs, Madas, or Pietro Fiorentini) controls manifold operating pressure. Regulators cannot cover both Natural Gas and LPG with a single spring: - Natural Gas Setup: Fitted with a low-rate Yellow or Blue Spring calibrated for outlet pressures between 15.0 and 27.5 mbar. - LPG Setup: Fitted with a high-rate Red or Black Spring calibrated for outlet pressures between 30.0 and 65.0 mbar. - During conversion, the spring housing cap is unscrewed, the spring swapped, and an external digital differential manometer connected to the downstream test nipple to adjust the set-screw under 100% full-fire burner demand.

---

4. Premix Combustion Aerodynamics & Excess Air Tuning (λ = 1.15 to 1.25)

Modern high-efficiency roasters utilize premix or partially aerated burners rather than raw diffusion flames. Achieving complete, soot-free combustion without producing toxic carbon monoxide (CO) or unburned hydrocarbons (THC) requires precise air-fuel ratio modulation across the entire firing range (10% low fire to 100% high fire).

`` +---------------------------------------------------------------------------------------------------+ | COMBUSTION FLAME APPEARANCE & STOICHIOMETRY DIAGNOSTIC | +---------------------------------------------------------------------------------------------------+ | OPTIMAL COMBUSTION (Excess Air Ratio Lambda = 1.18 - 1.22) | | Flame Appearance: Crisp, compact, luminous cobalt-blue cones with sharp inner core | | Flue Gas Analysis: O2 = 3.8% | CO2 = 9.8% (NG) / 11.8% (LPG) | CO < 30 ppm | NO_x < 35 ppm | | Drum Thermal Transfer: Clean, soot-free convection; 0.0 ppm taint on roasted beans | +---------------------------------------------------------------------------------------------------+ | RICH COMBUSTION (Fuel-Rich / Air-Starved, Lambda < 1.05) | | Flame Appearance: Lazy, flickering orange-yellow tips, long flame extending up drum shell | | Flue Gas Analysis: O2 < 1.5% | CO > 800 - 4,000 ppm (LETHAL) | Heavy black carbon soot | | Roastery Hazard: Soot insulates drum underside, carbon fouls burner ports, baked sulfur taint | +---------------------------------------------------------------------------------------------------+ | LEAN COMBUSTION (Excessively Air-Rich, Lambda > 1.45) | | Flame Appearance: Pale, noisy, fluttering flame with tendency to lift off burner ports | | Flue Gas Analysis: O2 > 6.5% | Thermal Efficiency drops | RoR sluggish; risks flameout lockout | +---------------------------------------------------------------------------------------------------+ ``

Electronic Flue Gas Analysis Verification Visual flame inspection alone is insufficient for commercial certification. A calibrated electronic combustion analyzer (measuring O₂, CO, CO₂, and NO) must sample exhaust gases upstream of the chaff cyclone:

| Flue Gas Parameter | Natural Gas Target | LPG Propane Target | Permissible Hazard Limit | | :--- | :--- | :--- | :--- | | Oxygen (O₂ %) | 3.5% – 4.5% | 3.8% – 4.8% | Never < 2.0% (danger of soot and explosion) | | Carbon Dioxide (CO₂ %) | 9.2% – 10.1% | 11.2% – 12.2% | Max theoretical: 11.8% NG / 13.8% LPG | | Carbon Monoxide (CO ppm) | < 50 ppm air-free | < 50 ppm air-free | Strictly < 100 ppm; shutdown at > 400 ppm | | Nitrogen Oxides (NO_x ppm) | < 35 ppm (Premix) | < 45 ppm (Premix) | Standard code limit < 60 ppm | | Flue Gas Temperature | 220°C – 280°C | 225°C – 285°C | Exceeding 340°C indicates exhaust over-firing | | Combustion Efficiency (η) | 88.5% – 92.0% | 89.0% – 92.5% | Lower indicates excessive diluting air |

---

5. Step-by-Step Workshop Conversion Protocol (Standard Operating Procedure)

This SOP covers converting an RC CAST-30 or RC IS-60 from Natural Gas to LPG (or reverse):

Phase 1: Isolation & De-energization (LOTO) 1. Shut down the roaster PLC and lock out the main electrical disconnect switch (NFPA 70E compliance). 2. Close the upstream gas supply ball valve and attach a safety padlock and warning tag (Lockout/Tagout - LOTO). 3. Bleed residual gas pressure from the manifold by loosening the pressure test point screw into a well-ventilated space until pressure reads 0.0 mbar on a digital manometer.

Phase 2: Mechanical Nozzle Swapping 1. Remove the protective burner lower access shield. 2. Disconnect the pilot flame gas line and the electronic spark ignition / flame ionization electrode assembly. 3. Unbolt the burner manifold pipe union and withdraw the injector manifold bar. 4. Using a 6-point brass socket wrench, remove existing nozzles. Inspect threads for galling. 5. Apply a microscopic drop of anaerobic gas-rated PTFE thread sealant (e.g., Loctite 567 or Gas-Tite paste) to new laser-drilled brass nozzles matching the target fuel table. Never use standard white plumbing tape, which shreds and plugs sub-millimeter nozzle orifices. 6. Torque nozzles evenly to 14–16 Nm.

Phase 3: Gas Train Regulator Spring & Pressure Switch Calibration 1. Unscrew the regulator top cap. Extract the low-pressure NG spring (Blue) and install the calibrated high-pressure LPG spring (Red). 2. Adjust the Low Gas Pressure Switch (LGPS) trip setting: for Natural Gas, set to 14 mbar; for Propane, set to 24 mbar. 3. Connect a dual-port digital manometer to the manifold test nipple.

Phase 4: Pressure Leak Testing & Purge 1. Pressurize the gas train with the burner valves closed. Perform a 10-minute static pressure decay test at 50 mbar. Zero pressure drop indicates hermetic sealing. 2. Apply certified bubble leak detector solution (e.g., Snoop) across all threaded joints, fittings, and solenoid flanges.

Phase 5: Firing Commissioning & Combustion Tuning 1. Power up the roaster control system and initiate pilot ignition sequence. 2. Adjust regulator set-screw under low fire (20% demand) to set baseline pressure. 3. Drive burner to 100% full fire. Adjust regulator set-screw until manifold pressure stabilizes at nominal rating (20.0 mbar for NG; 37.0 mbar for Propane). 4. Insert combustion analyzer probe into the cyclone exhaust flue. Adjust primary air shutter or premix blower VFD speed until flue gas reading achieves O₂ = 3.8%–4.2% and CO < 30 ppm. 5. Affix a durable metallic conversion nameplate onto the roaster chassis documenting: Date, Converted Fuel Type, Orifice Size, Manifold Working Pressure, and Commissioning Engineer signature.

---

6. Python Engineering Simulation Script: Burner Orifice Sizing & Wobbe Index Calculator

This verified Python engineering calculator computes fuel flow rates, combustion air requirements, Wobbe Index, and precise nozzle drill diameters for commercial coffee roasters.

```python """ RC-Tech Coffee Roaster Dual-Fuel Burner Conversion & Orifice Sizing Calculator Calculates Wobbe Index, volumetric fuel consumption, stoichiometric air demand, and precision injector orifice drill sizes for Natural Gas and LPG. """

import math from typing import Dict, Any

def calculate_burner_orifice_sizing( target_thermal_kw: float, fuel_type: str = "PROPANE_LPG", # "NATURAL_GAS", "PROPANE_LPG", or "BUTANE_LPG" manifold_pressure_mbar: float = 37.0, number_of_nozzles: int = 14, orifice_discharge_coeff: float = 0.85, ambient_temp_c: float = 20.0, ) -> Dict[str, Any]: # Fuel Thermodynamic Database (at 15°C, 101.325 kPa) fuel_db = { "NATURAL_GAS": { "name": "Natural Gas (Group H, Methane CH4)", "gcv_mj_m3": 38.5, # Gross Calorific Value "ncv_mj_m3": 34.8, # Net Calorific Value (LHV) "relative_density_d": 0.60, # Air = 1.0 "air_fuel_stoich_ratio": 9.52, "standard_nominal_mbar": 20.0, }, "PROPANE_LPG": { "name": "Commercial Propane (LPG G31, C3H8)", "gcv_mj_m3": 95.8, "ncv_mj_m3": 88.0, "relative_density_d": 1.52, "air_fuel_stoich_ratio": 23.86, "standard_nominal_mbar": 37.0, }, "BUTANE_LPG": { "name": "Commercial Butane (LPG G30, C4H10)", "gcv_mj_m3": 121.5, "ncv_mj_m3": 112.0, "relative_density_d": 2.01, "air_fuel_stoich_ratio": 30.94, "standard_nominal_mbar": 30.0, }, }

if fuel_type not in fuel_db: raise ValueError(f"Unsupported fuel: {fuel_type}. Select from {list(fuel_db.keys())}")

spec = fuel_db[fuel_type] air_density_std = 1.225 # kg/m^3 at 15°C gas_density = spec["relative_density_d"] * air_density_std

# 1. Wobbe Index (MJ/Nm^3) wobbe_index_mj_m3 = spec["gcv_mj_m3"] / math.sqrt(spec["relative_density_d"])

# 2. Required Volumetric Gas Flow Rate (m^3/h and m^3/s) # Target thermal power (kW) -> Energy demand (MJ/s = MW) # 1 kW = 0.001 MJ/s energy_rate_mj_s = target_thermal_kw / 1000.0 energy_rate_mj_h = target_thermal_kw * 3.6 vol_flow_m3_h = energy_rate_mj_h / spec["ncv_mj_m3"] vol_flow_m3_s = vol_flow_m3_h / 3600.0

# 3. Stoichiometric Combustion Air Required (m^3/h) # Target lambda excess air ratio = 1.20 lambda_excess = 1.20 combustion_air_m3_h = vol_flow_m3_h * spec["air_fuel_stoich_ratio"] * lambda_excess

# 4. Fluid Dynamics: Orifice Sizing via Torricelli Equation # Q = C_d * A_total * sqrt(2 * delta_P / rho_gas) delta_p_pa = manifold_pressure_mbar * 100.0 # 1 mbar = 100 Pa flow_velocity_ideal = math.sqrt((2.0 * delta_p_pa) / gas_density)

total_orifice_area_m2 = vol_flow_m3_s / (orifice_discharge_coeff * flow_velocity_ideal) area_per_nozzle_m2 = total_orifice_area_m2 / number_of_nozzles area_per_nozzle_mm2 = area_per_nozzle_m2 * 1e6

# Diameter per nozzle (mm) diam_per_nozzle_mm = math.sqrt((4.0 * area_per_nozzle_mm2) / math.pi)

# Approximate Numbered Wire Gauge Drill equivalent drill_sizes = [ (0.80, "#67"), (0.85, "#66"), (0.90, "#65"), (0.95, "#63"), (1.00, "#61"), (1.05, "#60"), (1.10, "#57"), (1.15, "#56"), (1.20, "#55"), (1.30, "#54"), (1.35, "#53"), (1.40, "#52"), (1.50, "#51"), (1.60, "#49"), (1.65, "#48"), (1.75, "#46"), (1.85, "#44"), (2.00, "#42"), (2.20, "#39"), (2.50, "#35"), ] nearest_drill = min(drill_sizes, key=lambda x: abs(x[0] - diam_per_nozzle_mm))

return { "fuel_type": spec["name"], "target_thermal_input_kw": target_thermal_kw, "manifold_pressure_mbar": manifold_pressure_mbar, "wobbe_index_mj_nm3": round(wobbe_index_mj_m3, 2), "volumetric_gas_flow_m3_h": round(vol_flow_m3_h, 3), "mass_gas_flow_kg_h": round(vol_flow_m3_h * gas_density, 2), "combustion_air_flow_m3_h": round(combustion_air_m3_h, 1), "excess_air_ratio_lambda": lambda_excess, "number_of_nozzles": number_of_nozzles, "total_orifice_flow_area_mm2": round(total_orifice_area_m2 * 1e6, 2), "single_nozzle_orifice_diameter_mm": round(diam_per_nozzle_mm, 3), "recommended_drill_gauge": f"{nearest_drill[0]:.2f} mm ({nearest_drill[1]} Wire Gauge)", }

# --- Simulation: Converting RC CAST-15 (28 kW) from Natural Gas to Propane LPG --- cast15_ng = calculate_burner_orifice_sizing( target_thermal_kw=28.0, fuel_type="NATURAL_GAS", manifold_pressure_mbar=20.0, number_of_nozzles=14, )

cast15_lpg = calculate_burner_orifice_sizing( target_thermal_kw=28.0, fuel_type="PROPANE_LPG", manifold_pressure_mbar=37.0, number_of_nozzles=14, )

print("=== RC CAST-15 (28 kW) NATURAL GAS CONFIGURATION ===") for k, v in cast15_ng.items(): print(f" {k}: {v}")

print("\n=== RC CAST-15 (28 kW) PROPANE LPG CONFIGURATION ===") for k, v in cast15_lpg.items(): print(f" {k}: {v}")

area_ratio = cast15_lpg["total_orifice_flow_area_mm2"] / cast15_ng["total_orifice_flow_area_mm2"] print(f"\nCalculated Area Ratio (LPG / NG): {area_ratio:.3f} (-{(1-area_ratio)*100:.1f}% reduction)") ```

---

Conclusion & Next Steps for Roastery Engineers

Dual-fuel flexibility safeguards a commercial coffee roasting operation against local fuel supply volatility, grid outages, and pipeline utility constraints while maintaining razor-sharp roast profile reproducibility.

#Dual Fuel Burner #LPG to Natural Gas #Burner Orifice Sizing #Wobbe Index #Premix Burner #Coffee Roaster Gas Conversion #Commercial Coffee Roaster #Low-NOx Combustion

Explore the machinery: RC ALP-1 · RC CAST-5 · RC CAST-15 · RC CAST-30 · RC IS-60 Industrial · RC IS-120 Industrial · RC DE30 Destoner · RC Destoner DE60 · RC Destoner DE120 · RC AFTB Coffee Gas Afterburner Series (AFTB1 / AFTB2 / AFTB3) · RC EXFUSION Smoke Dilution & Exhaust System · RC Industrial Coffee Cooling & Blending Mixer (MIX-60) · RC Premix Low-NOx Combustion Burner